Bore Gauges Explained: Measuring Internal Diameters Accurately
Bore gauges measure the inside diameter of a hole by pressing contact points against the bore wall and reading the difference from a known set size. General Tech Services supplies Mitutoyo bore gauges in the UAE and calibrates them in its own dimensional lab. This guide explains how they work, how to choose one and how to keep it accurate.
Machinists and quality inspectors know that a hole is harder to measure than a shaft. You cannot see the contact points, and a small tilt changes the reading. Well-chosen bore gauges and a sound setting routine remove most of that doubt.
What are bore gauges and how do they work?
A bore gauge is a tool for internal diameter measurement. Small contact points called anvils extend outward once the gauge enters the hole, and they touch the bore wall.
The gauge compares the bore with a setting standard. It then shows the difference on a dial or a digital display. Most bore gauges therefore read deviation from a set size, not an absolute value.
What types of bore gauges are available?
The terms cylinder test, hole test, bore mic, holtest and telescoping gauge all describe the same family of tools. They differ in construction and in how you set them.
• Two-anvil bore gauges are the most common and the lowest priced, and you set them with gauge blocks
• Internal micrometres, also called tri mics, use three anvils and are set with setting rings
• Plug gauges are the most basic type, with a plug on either end that differs slightly in size
Dial and digital versions add a readout. Our bore and hole gauges collection covers these formats.
Which Mitutoyo bore gauges does General Tech Services stock?
Mitutoyo instruments form the core of our range. The Mitutoyo bore gauges we list include dial, digital and small-hole models.
Examples with the specifications shown on our site:
• Mitutoyo 511-711, a dial bore gauge for 18 to 35 mm with 0.01 mm graduation
• Mitutoyo 511-714-20, a 2-point gauge for 100 to 160 mm with 2 micrometre accuracy
• Mitutoyo 511-746-20, an inch-range gauge with 0.0005 inch graduation and 2 micrometre accuracy
• Mitutoyo 511-207, a small-hole gauge for 0.4 to 0.74 inch with a self-centring bridge
The ABSOLUTE Borematic range adds digital readings to 0.001 mm, IP65 protection and data output for SPC systems. Browse the ABSOLUTE Borematic range for digital models. Product pages show free UAE shipping.
How do you set and use bore gauges for accurate readings?
Good internal diameter measurement depends on the setting step. The Mitutoyo 511-711 page notes that an optional inside-length standard, such as a setting ring, is required to set the gauge.
Follow these steps:
1. Clean the gauge, the setting standard and the bore.
2. Choose a setting ring or standard close to the nominal diameter.
3. Set the gauge to zero on the standard.
4. Insert the gauge into the bore and rock it gently to find the smallest reading.
5. Re-check the zero on the standard before you record results.
Repeat the check at several depths to spot taper in the bore.
Where do machinists and inspectors use these tools?
Our product pages describe bore inspection in workshop, quality control, industrial and laboratory settings. In each one, the job is the same: confirm that a hole meets its drawing size. Maintenance and calibration engineers also use them to check worn parts before they go back into service.
Which errors affect internal diameter measurement?
Most errors in internal diameter measurement come from the setup, not the gauge. Watch for these common causes:
• Dirt or oil on the bore, the gauge or the setting standard
• A setting standard far from the nominal size
• A gauge that is tilted instead of rocked to its smallest reading
• Worn contact points that nobody has checked
Fixing these habits improves results before any calibration is needed.
How do you choose between bore and hole gauges?
Start with the bore size, then match the tool to the job. Our bore and hole gauges collection lets you compare models side by side.
Check these points:
1. Measuring range and probe depth
2. Graduation or resolution
3. Stated accuracy
4. Metric or inch units
5. Data output, if you track results in SPC software
Choose a small-hole gauge when the bore is narrow. Choose a digital gauge when you need to record readings.
Why does bore gauge calibration matter?
Contact points wear, and setting standards can drift. Without bore gauge calibration, a gauge can pass every inspection while it measures slightly wrong.
Plan bore gauge calibration at an interval set by your quality system. Calibrate the setting rings and gauge blocks too, because they define the reference for every reading.
Our gauge blocks and sets range supports the setting step for two-anvil gauges.
What does dimensional calibration cover at General Tech Services?
Our calibration lab, known as General Construction Lab Calibration, serves industry with dimensional calibration and certified reporting. The scope includes ring, plug, snap and thread gauges, gauge blocks and micrometers.
We also calibrate measuring hand tools and masters. The lab instruments in our dimensional metrology area are traceable to NIST.
Read about our 17025 accredited calibration services and the EIAC-accredited lab behind them. For inspection work, see our CMM inspection services. For background, see the ISO/IEC 17025 standard and NIST.
Why buy from General Tech Services?
General Tech Services was founded in 1998 and became the authorised distributor for Mitutoyo. We now work with more than 80 trusted brands and serve more than 1500 clients across the GCC.
Our calibration lab and our product team belong to the same company, so you can buy a gauge and have it certified by us.
What should you check before buying bore gauges?
A short review prevents costly returns. Check these points before you approve bore gauges:
• The range covers your smallest and largest bore
• You have a setting ring or standard for the gauge
• The supplier is an authorised distributor with local support
• A calibration plan exists for the gauge and its standards
• Availability is confirmed in writing
Using one list for every order keeps your bore gauges purchases consistent.
FAQs
What is a bore gauge used for?
Bore gauges measure the inside diameter of holes and bores. Machinists and inspectors use them to check size, taper and roundness.
How do bore gauges differ from micrometers?
Bore gauges compare a hole with a set size, while micrometers measure external or internal size directly. Tri mics blur the line, because they use three anvils and setting rings.
Which Mitutoyo bore gauges suit small holes?
The Mitutoyo 511-207 covers 0.4 to 0.74 inch, and the 511-204 covers 10 to 18.5 mm. Both are small-hole models.
Does General Tech Services offer bore gauge calibration?
Yes. Our dimensional calibration covers gauges, micrometers and setting standards, and you receive a certificate for each item.
How often should bore gauges be calibrated?
Set the interval in your quality system and review it against past results. Recalibrate after any drop, repair or doubtful reading.
Order bore gauges from a local distributor today
Need genuine Mitutoyo bore gauges and traceable calibration? Call us on +971 6 5436933 or visit our head office in Sharjah.